- G4HFQ SOFTWARE YEASU FT 817 SERIAL
- G4HFQ SOFTWARE YEASU FT 817 DRIVER
- G4HFQ SOFTWARE YEASU FT 817 FULL
- G4HFQ SOFTWARE YEASU FT 817 SOFTWARE
- G4HFQ SOFTWARE YEASU FT 817 WINDOWS
G4HFQ SOFTWARE YEASU FT 817 SOFTWARE
The software did not need to be "installed" as it ran directly from the exe file! This is good.
G4HFQ SOFTWARE YEASU FT 817 SERIAL
Look for Ports (COM&LPT) and find the USB Serial Port, right click, Properties, Por Settings tab, Advanced button, and set your com port. Windows Key + R, type "devmgmt.exe" press enter. You will not be able to use the software if once your FTDI data cable is using a VCP higher than com:6.
G4HFQ SOFTWARE YEASU FT 817 DRIVER
This software must have been designed for computers prior to the virtual COM port driver (VCP).
G4HFQ SOFTWARE YEASU FT 817 WINDOWS
Using FT-817 WidebanderV4 was easy once Windows was forced to allow it on one of the lower comports. If you have the ft-817ND you will have to perform the hardware modification as described above. Note: This software does not work with the ND model, only the original ft-817. You can also use Widebander on the FT-857 and FT-897.
G4HFQ SOFTWARE YEASU FT 817 FULL
To set it back to the factory band plan you can do a full reset or run Widebander and press the button to put your radio back to standard. Widebanding the ft817 in this way makes no Permanent changes to the radio. Your results may vary depending on the default jumper positions during the time of your ft-817 production. HF transmission was not completely opened, however, some placed did open up, some of the MARS specific locations and also some others, yet some MARS frequencies were still blocked. After committing this configuration to my Yaesu the result was the full VHF / UHF range became unlocked. They make subtle changes resulting in variations within the same product line during production.Īccording to Yaesu's guide, Jumper pads 6,7,8 need to be CLOSED, 4,5,6 need to be OPEN, and 1,2,3 remain OPEN / unchanged. The mars modification guide from Yaesu indicates a different default configuration for the jumpers from the factory. Illustration: ft-817 serial range ON1503xx factory jumper solder pad configuration. The front panel needs to be disconnected and removed from the chassis to perform the mod. The solder pads controlling transmit and receive function are located behind the front panel. MARS CAP and Widebanding internal modification In February 2012, CHIRP gained support for programming the Yaesu FT-8×7 family of radios, thanks to efforts by Marco IZ3GME. Memory Channel 1 is used for Priority operation, and frequency information may only be over-written (not masked) on this channel. However, if you store new frequency information on a channel containing masked data, the masked data will be over-written and lost.Ħ. To restore the masked frequency data, repeat the above steps. Wait about three seconds when the memory channel number stops blinking, the data will now be "masked" and will not be available for operation.ĥ. The frequency display field on the LCD will go blank, and the memory channel number will blink.Ĥ. Press the (MW) key momentarily, then rotate the knob to select the memory channel to be deleted.ģ. Press the key momentarily, then rotate the knob, as needed, until Operating Function Row 2 appears on the display.Ģ. The deletion process is not a "hard" erasure, so if you erase a channel by mistake using this procedure, the memory channel contents can be recovered.ġ. Press and hold in the (MW) for one second until you hear a double beep the second beep confirms that the frequency information was successfully stored. Rotate the knob to select the channel number on which you wish to store the current frequency data.ĥ. The frequency stored (if any) on the current memory channel will be shown in the display.Ĥ. Press the key momentarily to enter the "Memory Check" mode, which is used to find an unused memory channel. Press the key momentarily, then rotate the knob as needed until Operatingįunction Row 2 appears on the display.ģ. Standard (default) repeater shifts do not require you to utilize the "split" frequency memoryĢ. If this is anįM channel, set up any required CTCSS/DCS and repeater shift configurations. Tune in the desired frequency, and set the operating mode and bandwidth. There are 200 normal memory channels numbered 1 - 200ġ. Short press and turn the dial until you see the correct option above on the soft key buttons under the display. When set, the SWR is displayed during transmit, otherwise the display indicates receive S meter. Home Key: Pressing this key momentarily recalls a favorite "HOME" frequency memory. Mode Keys: Pressing either of these keys momentarily will change the Operating mode. Scrolls the display through eleven rows of functions available for use via the, , keys.īand Down/Up Keys: Pressing either of these keys momentarily will cause the frequency to be moved up or When pressing the key, the current function of that key appears above each of the, , keys (along the bottom of the LCD) rotating the knob 5.3 MFJ-1899T HF telescoping multiband antenna 80M THRU 6MįUNC Keys: These three keys select many of the most important operating features of the transceiver.5.2 QRP whip Antenna Miracle / Miracle Ducker.
0 kommentar(er)
